stpfl

Brushless gimbals : AlexMos, Phobotic, Aligh vs Zenmuse combarison
i tested now zenmuse. You can not combare this with brushless gimbals :-( But for the price brushless gimbals are ok i think.

Comment by stpfl January 2015 permalink
Brushless gimbals : AlexMos, Phobotic, Aligh vs Zenmuse combarison
looks good. Ronin is also using encoders ...

Comment by stpfl January 2015 permalink
Brushless gimbals : AlexMos, Phobotic, Aligh vs Zenmuse combarison
do you think we could update one day our gimbals/motors with encoders? Especially for aerial shooting AM Gimbals are not accurate enough at the moment in my opinion. because i need something to work with at the moment i go with a zenmuse gh4 for n…

Comment by stpfl January 2015 permalink
Brushless gimbals : AlexMos, Phobotic, Aligh vs Zenmuse combarison
Cm3000 video looks good when hovering. if the speed increase the error increase as well. Not seen on the Zenmuse video. Why?

Comment by stpfl January 2015 permalink
Align Gimbal PID settings
I have vibration at higher speeds. Hz Reading where never use in older FW. I tried every firmwire since the beginning.

Comment by stpfl January 2015 permalink
Align Gimbal PID settings
So can i set 42 Hz Low pass filter in Simple BGC tool?

Comment by stpfl January 2015 permalink
Gimbal works fine until Pitch is panned down
Did you set a notch filter for Tilt axis?

Comment by stpfl January 2015 permalink
LeViteZer Gimbal test videos.
very stable! what are your pid settings? Autotune? Maybe FC Gain is a bit too high? But video looks fine.

Comment by stpfl December 2014 permalink
Higher D than P Value
Another Source of a guy using opposite PID Values http://www.simplebgc.org/pid-tuning.html http://www.simplebgc.org/images/basic.gif

Comment by stpfl December 2014 permalink
Yaw Drift while Pitching
is this a backdoor?

Comment by stpfl November 2014 permalink
Autotune - What's the definition of stability & precision?
Autotune - What's the definition of stability & precision?

Comment by stpfl November 2014 permalink
Temperature Drift
You can read in the Simple BGC manual that if there is a stronge temperature change you have to recalibrate your ACC. It would be intresting whats the normal operation range for ACC. For example if i make a precise 6 Point Calibration in 23C Room…

Comment by stpfl November 2014 permalink
Autotune - What's the definition of stability & precision?
its clear that you cannot remove the up and down bumps but maybe he meant the vibrations occur because of your footsteps. you can also see this in your video you posted. look at the left or right edge you will see some oszillation.

Comment by stpfl November 2014 permalink
Totally disallusioned
Hi! Was it a ARM BGC board?

Comment by stpfl September 2014 permalink
I set below 0.01?
If you use 0.01 because its the only option what really helps out its seems like you have a problem with your vibration dampening ( maybe to soft etc etc)

Comment by stpfl September 2014 permalink
32 bit 2 imu BG004 gimbal FS700 with 200mm zoom counterbalanced
nice, would you share PID Settings?

Comment by stpfl September 2014 permalink
"I" value
Did you try Follow Mode Speed?

Comment by stpfl September 2014 permalink
PID Settings for Flight different combared to Handheld?
Last video

Comment by stpfl September 2014 permalink
inaccurate yaw (aerial)
NOT SOLVED I thought the smaller error showing in BGC Gui would clean the problem out. But shaking is still there. http://youtu.be/EV-HTZUZPSg The best setting so far was 10 - 0.01 30 235

Comment by stpfl July 2014 permalink
2nd IMU above Yaw Motor
I tried 2nd IMU Above Yaw and found out it helps Yaw axis. But when you turn arround in non follow mode just once Pitch and Roll Axis loosing resolution. (more than 0.12 degrees error) I am thinking about changing back to IMU below YAW.

Comment by stpfl July 2014 permalink
2nd IMU above Yaw Motor
Answer from Alex : All depend on gyro calibration quality. 10 minutes is big enough time to have up to 10 degrees of drift, and it may increase in case of vibration, temperature changes. But from other hands 10degre drift for camera IMU is not big…

Comment by stpfl July 2014 permalink
inaccurate yaw (aerial)
SOLVED Made a short test with IMU above Yaw motor! Sucess :-)

Comment by stpfl July 2014 permalink
inaccurate yaw (aerial)
thanks for your suggestions! i have external landing gear. i already using batteries for dampening. when i mount my copter indoor and move it in small angles i get about 0.04 error in roll and pitch but 0.2 - 0.6 in yaw axis. i tried a lot pid …

Comment by stpfl July 2014 permalink
ARM BGC bad Support
if you have time to wait several months then yes

Comment by stpfl July 2014 permalink
Problems in high winds
try to lower gain from flight controll

Comment by stpfl July 2014 permalink
ARM BGC bad Support
Ok Thank you Version 4.5 arrived !

Comment by stpfl June 2014 permalink
ARMBGC 32bit burned
http://forum.basecamelectronics.com/index.php?p=/discussion/933/arm-bgc-bad-support

Comment by stpfl June 2014 permalink
ARMBGC 32bit burned
i still get no board from ARM BGC. I sent the board in April 10 It seems ARM BGC did not know by hisselft if they shippid it already

Comment by stpfl May 2014 permalink
ARMBGC Terrible Customer Service
Same here. Worst Support. No answered Mail. Shipping Duration forever...

Comment by stpfl May 2014 permalink
Voltage Error on the ArmBGC V 4.0 32-bit (Alexmos)
i sent mine back because of not good soldering skills in this size. What exactly was the problem why it burned? Was the old part defective?

Comment by stpfl April 2014 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: stpfl
Joined: December 2013
Visits: 101
Last Active: March 2015
Roles: Member