About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny Revision C
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
All versions
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
All Discussions
Troubleshooting
Can't do bode analysis
2 comments
Most recent by
jcobreros
February 2019
Troubleshooting
Single axis gimbal setup using encoder
5 comments
Most recent by
eoj121290
February 2019
Troubleshooting
Geopointing Using PWM
3 comments
Most recent by
Olz
January 2019
Troubleshooting
Speed of motor won't change
2 comments
Most recent by
AndrewSupport
January 2019
Troubleshooting
Power Connector Name
2 comments
Most recent by
AndrewSupport
January 2019
Troubleshooting
Alexmos Control Board Overheating
2 comments
Most recent by
KDMatt
January 2019
Troubleshooting
Power vs Battery
5 comments
Most recent by
peterarnold
January 2019
Troubleshooting
Center the Yaw at poweron
10 comments
Most recent by
AOPEN3434
January 2019
Troubleshooting
Mavlink to Arducopter- yaw spins slowly and other issues
3 comments
Most recent by
chen
January 2019
Troubleshooting
MavLink Control: no
2 comments
Most recent by
chen
January 2019
Troubleshooting
Yaw motor not stabilizing
3 comments
Most recent by
peterarnold
December 2018
Troubleshooting
Power is not set: Driver Fault (under-voltage, over-current, short circuit)
3 comments
Most recent by
peterarnold
December 2018
Troubleshooting
No raw encoder data using CAN Driver and AS5048B Encoder
3 comments
Most recent by
dfought
December 2018
Troubleshooting
DYS SUMMER-AIR problem with second axis
1 comment
Started by
mslowik
December 2018
Troubleshooting
Same motors output on all three motors while necoders are on
1 comment
Started by
SpookySpoon
December 2018
Troubleshooting
Pitch motor twitching up and down.
8 comments
Most recent by
alexmos
November 2018
Troubleshooting
Nebula 4300
1 comment
Started by
fl3xtra
November 2018
Troubleshooting
bluetooth hc-06 configuration
2 comments
Most recent by
turborocket
November 2018
Troubleshooting
BGC Extended with CANBus Driver not powering motors
1 comment
Started by
dfought
November 2018
Troubleshooting
Problem after restarting, if signal is presented on Aux1
2 comments
Most recent by
AndrewSupport
November 2018
Troubleshooting
Stabilization fault after some time camera operates
1 comment
Started by
SpookySpoon
November 2018
Troubleshooting
unstable when tilting to 90 degrees for- or backwards
5 comments
Most recent by
jcobreros
November 2018
Troubleshooting
Problem to balance Pilotfly H2 45 (wont hold the weight to calibrate when turned off)
2 comments
Most recent by
Benhudsonsaunders
October 2018
Troubleshooting
Frame imu fried?
4 comments
Most recent by
turborocket
October 2018
Troubleshooting
v2.63 encoder problem
7 comments
Most recent by
soul
October 2018
Troubleshooting
Firmware Update Failed... Gimbal no longer connects to computer.
3 comments
Most recent by
monsieurmeus
September 2018
Troubleshooting
GUI is not downloading firmware! Stuck on 0.00 firmware...
14 comments
Most recent by
monsieurmeus
September 2018
Troubleshooting
YAW only axis not returning to home
4 comments
Most recent by
lifeguard69uk
September 2018
Troubleshooting
I'm finding nebula5100 factory profile
1 comment
Started by
eapso
September 2018
Troubleshooting
no motors
1 comment
Started by
alfy
September 2018
Troubleshooting
‹
1
2
3
4
5
6
7
…
32
›
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
Categories
All Discussions
2,972
Getting started
585
Brushless gimbal mechanics
103
Electronics
438
Motors
141
Tuning brushless gimbal
327
Troubleshooting
943
Build logs, photo and video in work
37
Software (ideas, feature requests, bug reports)
277
Serial API
100
Links to manufacturers
21
Powered by Vanilla