About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
Vlad
Activity
Discussions
2
Comments
9
moves like a chicken.... what should I do?
I had the chicken dance on smaller gimbal. I eventually found that I had the axes configured wrong in the GUI. The default settings in the GUI were for the accelerometer and gyro board to be sitting horizontal though it was was fitted vertically. …
Comment by
Vlad
May 2014
permalink
DYS/gopro gimbal lost control
Hi. It rained all day yesterday, so no flying. Small window today. GOPRo battery died after 1 minute ( stupid boy) but here is it. I am getting vibration that I think comes from unbalanced props. But the serous wobbles start about 50 seconds in to…
Comment by
Vlad
May 2014
permalink
DYS/gopro gimbal lost control
HAHa. My sensor directions were wrong. I input Axis TOP = X RIGHT -Y and it stops spazzing out. Pitch looks good. Roll has some problems. Almost there. Now I need to play with the PIDs
Comment by
Vlad
May 2014
permalink
8 bit alexmos 3 axis controler error
HI. I am having the same problem with the IMU mounted to the camera. Simply spazzes out even after numerous 6 point calibrations. Any guidance or thoughts would be great.
Comment by
Vlad
May 2014
permalink
DYS/gopro gimbal lost control
HI. When you say sensor orientation I take it you mean the IMU? I also note to point Z axis parallel to motor but it does not make sense to me. I'm somewhat a newby. A clarification would be great. Look forward to the screenshot. Thanks. Vlad.…
Comment by
Vlad
May 2014
permalink
DYS/gopro gimbal lost control
A thought. I live very close to a US Embassy that emits a lot of RF signal all over the place. Could this have an effect on the acc calibration?
Comment by
Vlad
April 2014
permalink
DYS/gopro gimbal lost control
Hi. Thanks for the response. I try to. The message keeps saying that the accelerators need calibrating. I even tried the 6 axis calibration but no result. I will check the video of the 6 axis calibration again and throw myself into it...... again. …
Comment by
Vlad
April 2014
permalink
DYS/gopro gimbal lost control
Here it is.
Comment by
Vlad
April 2014
permalink
DYS/gopro gimbal lost control
P.S. I made a short video of the problem but don't know how to post it. Any suggestions? Vlad.
Comment by
Vlad
April 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
Vlad
Joined
April 2014
Visits
16
Last Active
September 2014
Roles
Member
Powered by Vanilla