BaseCam Forum is in "read-only" mode for now. Ask for Support if you need help with our products.

Vandepoel

YAW gradually adjust +/- 5 degrees as I pitch camera up/down in follow mode
Pressing the auto button in the followtab , next to the pitch button seems to fix the problem.

Comment by Vandepoel February 2014 permalink
YAW gradually adjust +/- 5 degrees as I pitch camera up/down in follow mode
I got it to work on my gopro gimbal afterall, not shure what i did but suddenly it worked. Now i have the same problem whit my large gimbal and its not going away, did everything restarted use defauld , acc cal but when activate follow the yaw rotat…

Comment by Vandepoel February 2014 permalink
YAW gradually adjust +/- 5 degrees as I pitch camera up/down in follow mode
Same here ... Is this a bug?

Comment by Vandepoel February 2014 permalink
32 bit Version with 2nd IMU
Nevr tought about that simple trick

Comment by Vandepoel January 2014 permalink
32 bit Version with 2nd IMU
Yep, has to be dead silent

Comment by Vandepoel January 2014 permalink
32 bit Version with 2nd IMU
.

Comment by Vandepoel January 2014 permalink
32 bit Version with 2nd IMU
its been there for a while already

Comment by Vandepoel January 2014 permalink
Using hand held gimbal platforms for motion - dollys, vehicles, skates
Im going to use your video tomorrow on a big exibition in belgium, its a 2 days exibition where every cameraman of belgium will be present , i have to represent my product and so i can show what our gimbals are capable of ( landscapes at your home …

Comment by Vandepoel January 2014 permalink
Using the EasyRig Mini with AlexMos Gimbals
Okii usb controller

Comment by Vandepoel January 2014 permalink
Using hand held gimbal platforms for motion - dollys, vehicles, skates
i think you are good to go and make the tv world a little bit smoother ... im thinking of learning also to roller skate ... :) im now developing a car mount system, fast and easy with 3 suction holders wich hold the gimbal but stil to much vibration…

Comment by Vandepoel January 2014 permalink
4 axis hand held gimbal
http://youtu.be/fCCdcvnfDlM :)) our main man at work

Comment by Vandepoel January 2014 permalink
Yaw control not holding on handheld gimbal
yep, i redisigned mine to to get the pitch arm lower for heavyer setup. when go with such a heavy lens make sure your D faktor of the pitch is high enough. go much to high like D 40 until its buzzing and then lower the value until its good .... use …

Comment by Vandepoel January 2014 permalink
Follow Mode in 2.3B5
gone try it tomorow when im home, i have a shoot for redbull where they gone use my gimbal for the steady shots ... im curious how it will go ... keep u up to date

Comment by Vandepoel January 2014 permalink
Follow Mode in 2.3B5
Ha haaa, i even didnt noticed it until i saw my name :) ... Looking good like this ... I would say keep it like this, didn notice any remarkeble horizon off also and footage is stable all the way .... One question what do you mean by set angles by h…

Comment by Vandepoel January 2014 permalink
Yaw control not holding on handheld gimbal
Dear zeb, indeed i strugled a while in the beginning with this thinking theres not enough torque, The solution is very simple, loosen the yaw motor and slide it forward or backward, small time each time, tighten it again and try again. If you move …

Comment by Vandepoel January 2014 permalink
Follow Mode in 2.3B5
Nice to see you now and some implements of me on the other side of the world :) If you want to know how i look go to my site www.soundq.be :) Indeed, the i on pitch is the speed that you want it to follow , for everyone different how fast you wan…

Comment by Vandepoel January 2014 permalink
RC Tilt & Yaw affecting Roll (does not stay level)?
You should also in the rc tab below where the roll says -45 degress and 45 degrees, set it both to 0. I have only a little bit roll when i use a analog joystick for the pitch, when i tilt it down the roll goes 1 or 2 degrees of. But not on yaw.

Comment by Vandepoel January 2014 permalink
Trouble with Yaw Joystick at follow mode
Follow pitch yaw. Start should be 90 and mix 0, but not shure this will fix

Comment by Vandepoel January 2014 permalink
Trouble with Yaw Joystick at follow mode
Hi, no imediate idea what can be wrong. Shure you select pwm or analog

Comment by Vandepoel January 2014 permalink
Follow Mode in 2.3B5
Solution for switching profiles and shakes happen is put folow on in profile 1. Put follow off in profile 2. Then make shure its startup in profile 1 by pressing write again in profile 1 and disconect from gui. Now it startup in folow mode and switc…

Comment by Vandepoel January 2014 permalink
Follow Mode in 2.3B5
Hi aircam, Some tips from my gimbals. The roll should be inverted, P set to 35 and i to 0,35 D 20 . This higer values eliminate your roll is moving along your long left to right movement, decrease deadband to 2,5 and you horizon will be almost perfe…

Comment by Vandepoel January 2014 permalink
Changing profiles mid flight
Indeed

Comment by Vandepoel January 2014 permalink
Trouble with Yaw Joystick at follow mode
Discribe in more detail when what happens? Is it emitiatly turning and keeps on turning? , or is it when you touch the joystick?

Comment by Vandepoel January 2014 permalink
32 bit Version with 2nd IMU
Waiting for same info ... Today a client where the horizon drifts in some directions, but always come back to perfect level. Next startup again perfect level but other direction drift littlebit. Not much but its there . Never can tell wich time it w…

Comment by Vandepoel January 2014 permalink
I2C ERRORS
I had one time put 2 ferrite rings on my imu cable close to the board on a 45cm wire, the imu wire going from the yaw board to the sensor, not the imu cable between the main board and yawboard.Most of the time it was fixed by one ferrite ring.( well…

Comment by Vandepoel January 2014 permalink
Power-on shakes and rolls
Just push it back by hand the pitch if it does that. Make sure when u startup the camera is pointing straight forward, also can lean more to the back but not to the front downwards. I had this problem when i startup my rig and my camera was pointing…

Comment by Vandepoel January 2014 permalink
RC Settings - No action explanation
Or trim in the rc tab of the gui

Comment by Vandepoel January 2014 permalink
My card does not work anymore
I had this one time, microprocessor bad soldered, i sended it back and got a new one.

Comment by Vandepoel January 2014 permalink
Using the EasyRig Mini with AlexMos Gimbals
hey, yeah this is higly vissible on the roll when setting deadband to high. i found out when setting the deadband to 0 and expo curvo also to 0 its gone the slow afterroll ... also tryed deadband 2.5 degrees and expo curvo to 0 , this is also bette…

Comment by Vandepoel January 2014 permalink
Using the EasyRig Mini with AlexMos Gimbals
Everything i have until now i bought on goodluckbuy. Since 6 months for every day i am pressing on the new arrivals tab to see whats comming out new. Here i fount the 8108 90t motors. But i would recomand the gm81 90t closed housing(same price) on r…

Comment by Vandepoel January 2014 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: Vandepoel
Joined: December 2013
Visits: 75
Last Active: November 2014
Roles: Member