About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
AndrewSupport
Activity
Discussions
Comments
303
Sensor not connected
Hello, whoobs, try upload recovery firmware in Manual mode and then upgrade board in Automatic mode. Where did you get that board? In our webstore or?
Comment by
AndrewSupport
June 2015
permalink
Sudden configuration loss
Hello, What versions of the GUI and firmware are you using?
Comment by
AndrewSupport
June 2015
permalink
Pitch not Working?
Hello, Please, send schematic diagram with connections. And take a photo where we can see connections RC, servo and control board.
Comment by
AndrewSupport
June 2015
permalink
SimpleBGC camera shake
Hello, P values must be higher than D. Try to use PID autotuning.
Comment by
AndrewSupport
June 2015
permalink
Pitch motor held by power, not responding to movement
Hello, Please, send screenshot of Basic and Advanced tab of the GUI.
Comment by
AndrewSupport
June 2015
permalink
Compass acting weird
Hello, Kwinto, Try re calibrate Gyro.
Comment by
AndrewSupport
June 2015
permalink
What up with the ROLL (X axis) not holding level?
Hello, Please, make a photo of whole your gimbal and place where you mount IMU sensor. And place photos here.
Comment by
AndrewSupport
June 2015
permalink
alexmos issue
Hello, What version of control board on your gimbal? 8bit or 32bit?
Comment by
AndrewSupport
June 2015
permalink
Pitch jumps / twitches away from level, then slowly goes back to level - endlessly
Hello, Please, take a video where it will be visible and the work gimbal and GUI.
Comment by
AndrewSupport
June 2015
permalink
Reset firmware 32 bits
Hello, If automatic upgrade fails just after downloading firmware from our server (for example, there could be problems upgrading when using a Bluetooth connection under Mac OS), you can try to upload firmware in the manual mode. You can find the d…
Comment by
AndrewSupport
June 2015
permalink
Auto Tune returns 0.00 for "I" in Yaw axis.
Hello, We recommend you update your board to latest firmware and use latest GUI: http://www.basecamelectronics.com/downloads/32bit/#latest I – The “I” value changes the speed at which the gimbal moves to incoming RC commands and to move the gimbal…
Comment by
AndrewSupport
May 2015
permalink
help with yaw not centering on 32-bit board!!
Hello, imrj, check balance of YAW axis. And try increase POWER parameter.
Comment by
AndrewSupport
May 2015
permalink
Pitch twitch
Hello, dimvasilk, Check your gimbal in the hands and indoors without using quad. If this problem is not, use of more hard dampers for vibration damping.
Comment by
AndrewSupport
May 2015
permalink
Pitch twitch
Hello, Link to your video doesn't work. Please, send a link again.
Comment by
AndrewSupport
May 2015
permalink
One day I will will tell my sons: I nearly tunned an alexmos board..
Hello, Possible something wrong with a balance of ROLL axis. Check balance. And try autotune only for ROLL by start from zero values. If this will not help you, try to change PWM frequency: http://ybex.com/d/ayl2ii4fz8lh6fxddilp2lfc8l19bmsqhgx6tok1…
Comment by
AndrewSupport
May 2015
permalink
YAW motor not responding
Hello, Please, send us photos of both sides of your board in high resolution. Possible, driver of YAW axis lost some parts.
Comment by
AndrewSupport
May 2015
permalink
USB and Lipo connected simultaneously, is it OK?
Hello, Upload photo to dropbox.com and place link a link here.
Comment by
AndrewSupport
May 2015
permalink
Shaking/ weird movements
Hello, Check your gimbal for gaps in the joints. Also increase hardness of your gimbal. As see on second video, you need better calibrate Gyro and Acc. For example, try calibrate Acc by six positions.
Comment by
AndrewSupport
May 2015
permalink
RCTimer 32bit Problem
Hello, You need to UPGRADE your board in Automatic mode to latest firmware. After this you can tune your gimbal.
Comment by
AndrewSupport
May 2015
permalink
After firmware upgrade, can't connect to the board
Hello, No, its Chinese controller. This is the feature of Chinese controllers, they can be flashed, but after that did not work.
Comment by
AndrewSupport
May 2015
permalink
How to reset EEPROM in tiny 32 bits
Hello, What you mean from "alarm start to ring quickly"? Flashing LEDs onboard?
Comment by
AndrewSupport
May 2015
permalink
Tiny32 2.50 upgrade problems
Hello, Please, Install DFU driver as it's described in manual: http://www.basecamelectronics.com/files/v3/SimpleBGC_32bit_manual_2_50_eng.pdf
Comment by
AndrewSupport
May 2015
permalink
I2C Sensor not connected
Hello, Please, check: 1) connectors 2) cable to to IMU 3) LED on the IMU board need to light on, then you connect board via USB or battery.
Comment by
AndrewSupport
May 2015
permalink
After firmware upgrade, can't connect to the board
Hello, Our software is not compatible with Chinese controllers.
Comment by
AndrewSupport
May 2015
permalink
Firmware "Failed to Upload Error"
Hello, cbpagent72, possible, antivirus software to block a program. Try disable antivirus software and upload board again.
Comment by
AndrewSupport
May 2015
permalink
GoPro Gimbal's motors
Hello, You need sensorless motor, because the feedback works through the IMU and microprocessor, which processes the data from the IMU. But if you need better quality, you can use encoders for each motors and a special firmware. For small camera, li…
Comment by
AndrewSupport
April 2015
permalink
My 7800 32bit 3 axid gimbal is moving like its possessed! HELP!
Hello, Try re-calibrate Gyro and accelerometer.
Comment by
AndrewSupport
April 2015
permalink
Issue on startup
Hello, Please, take a screenshot of Basic tab of the GUI and place here.
Comment by
AndrewSupport
April 2015
permalink
NEBULA 4000 Firmware upgrade?
Hello, What GUI version are you using for upgrade? Please, send screenshots of errors.
Comment by
AndrewSupport
April 2015
permalink
BMG5208-200 correct order connection cable
Hello, Connect the motor wires to the board in any sequence.
Comment by
AndrewSupport
April 2015
permalink
More Comments
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
AndrewSupport
Joined
October 2014
Visits
399
Last Active
February 15
Roles
Member, Administrator, Moderator
Powered by Vanilla