About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
futurebreeze
Activity
Discussions
4
Comments
7
DYS GoPro alex mos 8 bit - rolling during yaw
I have a GoPro DYS 3axis gimbal with and I managed to tune it properly eventually. As a matter of fact my initial issue was that over a certain angles of inclination the roll axis was trembling disturbing the yaw axis too. After I fed signal from t…
Comment by
futurebreeze
April 2015
permalink
Alexmos 8bit - different behavior 2.30 vs. 2.40, shaking YAW axis
I am back with good and bad news. Good news is that I managed to properly re-tune the DYS gimbal from scratch, I started as Alexmos manual says, low values PID and progressively increases them watching for oscillations. The result is pretty good, I …
Comment by
futurebreeze
March 2015
permalink
Alexmos 8bit - different behavior 2.30 vs. 2.40, shaking YAW axis
OK, i'll try to re-tune from scratch, I've already did this but, never know, a new start could mean success. Thanks!
Comment by
futurebreeze
March 2015
permalink
Alexmos 8bit - different behavior 2.30 vs. 2.40, shaking YAW axis
Hi Garug, Sorry for the long video, I just wanted to show the circumstances the issue is occurring. Jump straigt to 1:34.
Comment by
futurebreeze
March 2015
permalink
Bluetooth
Check the serial baud rate value set in GUI. This value must be the same as the transceiver's default baud rate. Try to change to 115200 in GUI, this might be the default value of the transceiver.
Comment by
futurebreeze
October 2013
permalink
Switch Angle Mode to Speed Mode without entering the GUI
Oh, profiles, of course...it was so simple! How didn't I think about it? This board is a very good product and your support is very good on this forum. Thank you very much!
Comment by
futurebreeze
September 2013
permalink
USB and Lipo connected simultaneously, is it OK?
OK, that's great, I'll be less nervous with the future configuration operations :). In the meantime I managed to connect to the board through a Bluetooth module. Thanks Alex!
Comment by
futurebreeze
September 2013
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
futurebreeze
Joined
September 2013
Visits
18
Last Active
October 2016
Roles
Member
Powered by Vanilla