About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
ptunstall
Activity
Discussions
3
Comments
11
YAW gradually adjust +/- 5 degrees as I pitch camera up/down in follow mode
I pressed that button and it then made it impossible to find the level position for Pitch. there are notches where the camera gimbal wants to sit and for some reason when it hits level it'll jump off and skip to an unlevel notch. I am using t…
Comment by
ptunstall
February 2014
permalink
YAW gradually adjust +/- 5 degrees as I pitch camera up/down in follow mode
I have spent a large amount of time trying to get it to work and I eventually gave up and reverted back a version in firmware. I wasn't happy with the high frequency vibrations that would show up when using a joystick. I wasn't happy with…
Comment by
ptunstall
February 2014
permalink
Firmware 2.4 woes
Ok so I figured it out (I think) He's adjust the power control over the motors which changes the PIDs dynamic. I defaulted my who rig and started fresh ignoring all instincts. I kept dialing in values till I got a steady result. My D is now…
Comment by
ptunstall
February 2014
permalink
Firmware 2.4 woes
My rig is acting erratic after the upgrade. No amount of adjustments seem to fix this either. I even ran defaults and went back to rebuilding my PIDs with very diminishing returns...
Comment by
ptunstall
February 2014
permalink
Firmware 2.4 woes
I am having the exact same problem. I have no idea how to resolve it. Anyone have any luck?
Comment by
ptunstall
February 2014
permalink
Serious calibration problems
if you have your rig sitting flat in the correct orientation then in your realtime graph one of the 3 accelerometer AXIS should have an offset value which is coming from gravity. This your TOP axis so set that in the sensor box of the basic tab. …
Comment by
ptunstall
January 2014
permalink
Serious calibration problems
It sounds like you've mounted the IMU incorrectly if the dials in the application do not correctly correspond to the motion of the IMU. You can switch the "AXIS Top" and "AXIS Right" settings to correct this without the nee…
Comment by
ptunstall
January 2014
permalink
Parallax 27800-RT thumb stick Smokes after about 2 minutes of offset control
So I seem to have solved the issue! I switched pulling 5v from the 3 pins on the RC input to pulling 5v from Vcc and the pot switch no longer is getting hot!!! Thanks for the assistance man!
Comment by
ptunstall
January 2014
permalink
Parallax 27800-RT thumb stick Smokes after about 2 minutes of offset control
Thanks I'll be getting another joystick this evening and I'm going to check into all of this!
Comment by
ptunstall
January 2014
permalink
Parallax 27800-RT thumb stick Smokes after about 2 minutes of offset control
Yes that is correct, I used that diagram actually to hook it up. I did find something odd early on in my research which later disregarded until now: http://aerialpixels.com/support/alexmos-joystick-connections/ these guys show the +5v being ignore…
Comment by
ptunstall
January 2014
permalink
Parallax 27800-RT thumb stick Smokes after about 2 minutes of offset control
So based on this diagram http://www.basecamelectronics.com/files/v10/SimpleBGC_connection_diagram.pdf I am connecting to the 5v and ground of the RC_Pitch input. I am then connecting the U/D and the L/R to the PWM(analog in my case) pins for RC_Pit…
Comment by
ptunstall
January 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
ptunstall
Joined
January 2014
Visits
22
Last Active
March 2014
Roles
Member
Powered by Vanilla