About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
KevinH92
Activity
Discussions
1
Comments
9
Yaw problems
Oke, i played a lot with PID tuning by hand. The auto version is like shit it seems. I finally found a movie on YouTube that explained it how PID works. And so i could put in the numbers myself en try. It worked fine. It's not 100% perfect i th…
Comment by
KevinH92
March 2016
permalink
Yaw problems
Wel normally it does crazy with no errors at all. So i am not sure if that is the problem, or just a problem. And it is hard to find the point that the errorproblem is over i think if it has nothing to do with eachother. Becouse the error problem is…
Comment by
KevinH92
February 2016
permalink
Yaw problems
I was just playing with the PID numbers. And my gimbal started beeping crazy and GUI said emergancy stop for I2U errors. The errors right on the screen where just counting up, i pulled the plug at 5963 errors... Getting kind of crazy from this...
Comment by
KevinH92
February 2016
permalink
Yaw problems
The I2C/IMU has indeed conection problems it seems. Sometimes it doesn't work at start or randomly dont work anymore.
Comment by
KevinH92
February 2016
permalink
Yaw problems
I read the following in the manual: NOTE: It is advisable to pull each motor cable through (and make at least one loop around) a ferrite ring to avoid high frequency interference from affecting the IMU sensors and other electronic devices (both on …
Comment by
KevinH92
February 2016
permalink
Yaw problems
I am not acacly sure how to set up the meter, but the highest number i get is 00.9 at 200M of the ohm side. But that is the same for all motors. The YAW motor also works normally to the others when the IMU is not connected. The motors are just powe…
Comment by
KevinH92
February 2016
permalink
Yaw problems
So i have to put the sticks of the meter to 2 of 3 and check it. And so on till i have had any combination of checking?
Comment by
KevinH92
February 2016
permalink
Yaw problems
With the PID tuning i think? Well i did various times but it stays this way. Well i have one, but how i read that out?
Comment by
KevinH92
February 2016
permalink
Yaw problems
Comment by
KevinH92
February 2016
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
KevinH92
Joined
February 2016
Visits
4
Last Active
March 2016
Roles
Member
Powered by Vanilla