About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit Tiny
Revision B
3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Partners
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
Get Trial Firmware
Buy Fully-functional Firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
All versions
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
RU
CN
Discussions
Activity
Sign In
All Discussions
Getting started
Belt driven roll axis not enough speed...
1 comment
Started by
adrianni
June 29
Getting started
CAN_MCU board to use CAN drivers AND I2C drivers simultaneously
1 comment
Started by
adrianni
June 12
Getting started
What does 'Emergency stop: SUB-CODE 40' mean?
3 comments
Most recent by
JuntaePark
May 18
Getting started
SimpleBGC 32bit Lock mode for yaw (+ yaw drifting)
3 comments
Most recent by
mohsein
April 1
Getting started
CAN_MCU connection to Mac OSX
3 comments
Most recent by
AndrewSupport
March 31
Getting started
Emergency Stop: Battery voltage is higher than expected at startup sequence
4 comments
Most recent by
alexmos
March 26
Getting started
Came tv 7800 gimbal
2 comments
Most recent by
Thematrix
March 18
Getting started
RC setting and Gimbal motor controls using arduino
3 comments
Most recent by
umairaziz
March 2
Getting started
Manual Control of Gimbal
8 comments
Most recent by
umairaziz
February 29
Getting started
Follow mode in Angle Control
4 comments
Most recent by
AdrienT
February 19
Getting started
Gimbaled model rocket motor mount? Anyone here has done something like that?
2 comments
Most recent by
AOPEN3434
January 29
Getting started
Authenticity?
1 comment
Started by
zoidy
January 25
Getting started
I flight gimbal controller
3 comments
Most recent by
niju
January 15
Getting started
MODE_SPEED doesn't work for yaw,MODE_ANGLE doesn't work for roll
2 comments
Most recent by
alexmos
December 2019
Getting started
Connecting encoders (pwm) and mavlink (pixhawk) to SimpleBGC 32-bit
3 comments
Most recent by
ronsand
December 2019
Getting started
re-fitting a Ronin Gimbal
4 comments
Most recent by
Try2ki55me
October 2019
Getting started
Standard servo instead of the bldc motor to drive the gimbal
3 comments
Most recent by
dano
October 2019
Getting started
Power consumption
3 comments
Most recent by
eutico
September 2019
Getting started
Basic setting profile for ikan MS-PRO
1 comment
Started by
raminmazur
September 2019
Getting started
Sensor is not connected, Accelerometer is not calibrated
3 comments
Most recent by
AOPEN3434
August 2019
Getting started
Yaw motor very slowly rotating to the left ( old issue but very much still present)
2 comments
Most recent by
AndrewSupport
August 2019
Getting started
Limting angle of camera
3 comments
Most recent by
alexmos
July 2019
Getting started
Documentation on the gui dials, what does it all mean?
3 comments
Most recent by
gusisin
July 2019
Getting started
base cam problem
1 comment
Started by
elec86
July 2019
Getting started
Pitch speed mode not working
2 comments
Most recent by
alexmos
July 2019
Getting started
two motors one Axis
12 comments
Most recent by
Garug
July 2019
Getting started
Birdy Cam 2 acting crazy
1 comment
Started by
mazaya
June 2019
Getting started
Serial API + GPS to follow a moving target
7 comments
Most recent by
camoflush
May 2019
Getting started
Anyone used the VN-200 IMU?
6 comments
Most recent by
bit
May 2019
Getting started
Do I need IMU for Encoder Firmware
3 comments
Most recent by
Garug
May 2019
Getting started
‹
1
2
3
4
5
6
7
…
19
›
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
Categories
All Discussions
2,776
Getting started
547
Brushless gimbal mechanics
97
Electronics
410
Motors
130
Tuning brushless gimbal
310
Troubleshooting
881
Build logs, photo and video in work
37
Software (ideas, feature requests, bug reports)
262
Serial API
83
Links to manufacturers
19
Powered by Vanilla
