About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
Mrimstad
Activity
Discussions
8
Comments
80
RCTimer GMB 5208 024-200T
this is normal behavior for a 3phase motor.
Comment by
Mrimstad
September 2014
permalink
Alexmos "Auto Tuning"
I would gladly sacrifice some functions for auto tune firmware...
Comment by
Mrimstad
September 2014
permalink
Alexmos "Auto Tuning"
Then once again, why dont we have this on 8bit?
Comment by
Mrimstad
September 2014
permalink
Gimbal axis order
no vibration dampening, but that i assume is only a prototype.
Comment by
Mrimstad
September 2014
permalink
Alexmos "Auto Tuning"
phobotic does it with 1 imu so why cant alexmos boards?
Comment by
Mrimstad
September 2014
permalink
Gimbal axis order
I have noticed that the dys smart gimbal aswell can have the axis orders mixed upp. As far as i know this is a 8bit design board. So what is so special about it that makes this possible? https://www.youtube.com/watch?feature=player_embedded&v=D…
Comment by
Mrimstad
September 2014
permalink
Boards compability
If it is not an official supported alexmos card it will either not work after the uppgrade, or you wont be able to uppgrade at all. Anyway you can flash back the nulled firmware. Some report of it not working but many report it does. Its a gamble yo…
Comment by
Mrimstad
August 2014
permalink
Boards compability
the color of the pcb doesnt realy tell you anything.
Comment by
Mrimstad
August 2014
permalink
Running IMU through slip ring
not even using the slip ring. wires just snaked trough the rather large hollow shaft.
Comment by
Mrimstad
August 2014
permalink
No power to yaw when gui is connected
The gimbal is working with yaw both normal and in follow mode so i guess i have it setup correctly. Its just a pain to tune when you cant watch the gui. Im sure others have had the issue aswell
Comment by
Mrimstad
August 2014
permalink
Running IMU through slip ring
running imu trough one hollow shaft. No unpredictable results
Comment by
Mrimstad
August 2014
permalink
PID problem on my 3axis steadi with 32bit alexmos...
to weak motors for that camera/lens combo
Comment by
Mrimstad
August 2014
permalink
yaw will not return to home from one side in follow mode 8bit
Have seen this on a 3axis dys card aswell. Any ideas where to start?
Comment by
Mrimstad
August 2014
permalink
yaw will not return to home from one side in follow mode 8bit
Another problem is that i cannot follow this in the gui. Wile connected i get no power to the yaw motor. So tuning is realy hard to be honnest. deadband is at the normal 5 deegres
Comment by
Mrimstad
August 2014
permalink
yaw will not return to home from one side in follow mode 8bit
I guess im still alitle fresh to the bgc world, what do you meen by carry out the acc? I did the gyro and acc calibrations as per manual. took the imu of an mounted it to a box for easyer leveling. When i do any motion it will stay aligned if thats…
Comment by
Mrimstad
August 2014
permalink
Best replacement roll motor?
Ipower seems like solid performers. I use the hollow shaft ones. Larger shaft less play.
Comment by
Mrimstad
August 2014
permalink
Gimbal axis order
So no hope for 8bit users ? :\
Comment by
Mrimstad
August 2014
permalink
Gimbal axis order
I dont know what controller this gimbal uses but as you can see. the axis order is what i have, and it starts upp as it should. So there should be an option to select the axis order for uss sbgc users aswell please.
Comment by
Mrimstad
August 2014
permalink
Gimbal axis order
Would realy like to see a solution to this aswell. My current n5 gimbal build is setup with pitch/yaw/roll and i would realy like to use it as is withouth having to rebuild it.
Comment by
Mrimstad
August 2014
permalink
Infomation required: BeHolder Lite with BGC-v3.11 circuit board
Pictures help
Comment by
Mrimstad
August 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
Mrimstad
Joined
August 2014
Visits
110
Last Active
July 2015
Roles
Member
Powered by Vanilla