About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
Ecopter
Activity
Discussions
Comments
9
Need info on WIND BASECAM electronics 3-axis AlexMos board
HI, are you sure it is a 8 bit controller and not a 32 bit one ? 2 x IMU are used on the 32 bit more likely i think, BEst regards, Fabien
Comment by
Ecopter
May 2014
permalink
About Inertia and PID tuning
HI, i experienced the same problem on many gimbals installations, and in these cases, relocating the IMU PCB or changing it's orientation( mechanically and of course in the software) solved the problems most of time. BE careful also with ultra…
Comment by
Ecopter
May 2014
permalink
Roll drift 2-3%, 32Bit HIfly Hand held
Hi, a simple way to solve this is to lock the roll arms on a table or anything, put the motors on " OFF" position, and then move the pitch axis by hand. If you see the blue arrows indicators on Pan and Roll move when you rotate the Pitch …
Comment by
Ecopter
May 2014
permalink
moves like a chicken.... what should I do?
Hi, make sure also that you are in fixed mode when you setup your gains. The I on the Pan seems pretty high.. If you a re in follow mode, you have to bring back the gimbal in level and alignment position by hand as it detects angle from BEMF of moto…
Comment by
Ecopter
May 2014
permalink
Voltage
Hi, this depends of the lenses and equipment + weight of the gimbal itself. You can use 3S lipo, with a power that will be between 80 and 180 ( the more axis the motor has in front of it, the more power you need : tilt needs few, roll needs a bit m…
Comment by
Ecopter
May 2014
permalink
osilications with extreme angles
Hi, make sure of 2 things, first is that the gimbal glance AND geometry is PERFECT ( many gimbals have a very bad geometry, arm lengths differences, alignment..) ... Then Balance is the most delicate thing at extreme angles. The basic test to make a…
Comment by
Ecopter
May 2014
permalink
Problem connecting Alex Mos Board to Mikrokopter Flight Control V2.5
Hi Christoph, i had that problem with a customer 2 weeks ago, make sure to use the right SVC plug and also to make sure that you do not invert signal and ground connexion on the Alexmos board connection for the RX Pitch connector ( or the gimbal wi…
Comment by
Ecopter
May 2014
permalink
manque de documentation
Bonsoir, la carte troisième axe doit être raccordée sur SCL /SDA de l'i2C, le power et la masse sont celles pour 'l'alimentation générale de la carte ( lipo). LEs boutons doivent être des boutons instantanés ( fugitifs), sinon ce s…
Comment by
Ecopter
May 2014
permalink
calibration of gyroscope
Hi, the calibration that is done at startup is only the Gyro., all you need is to put the gimbal on stable or something and lock the pitch axis ( where the sensor is located) time for the startup. To calibrate ACC with the button you need to enable…
Comment by
Ecopter
May 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
Ecopter
Joined
May 2014
Visits
0
Last Active
May 2014
Roles
Member
Powered by Vanilla