About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
KlausK
Activity
Discussions
3
Comments
11
Meaning of incorrect pole settings
As far as I know, auto-detecting poles might fail and you should put in the real number (count of motor-magnets), but if "invert" was detected, you should keep it. If it really indicates something above this, I cannot answer.
Comment by
KlausK
September 2018
permalink
Roll, Yaw Axis drift, Nebula slant 5100
Video is not visible here. Can you post a link to the video?
Comment by
KlausK
August 2018
permalink
Please clarify motor current SimpleBGC v3.x
Thanks Andrew for answering. While I fully understand what you are telling me, I still wonder about that hardwaredesign. You are telling me, that each of the three motordriver could provide up to 1,5 amps to a single motor, but all three together a…
Comment by
KlausK
July 2018
permalink
Optimal input voltage for BaseCam SimpleBGC 32-bit Extended on the bench? Total max motor current?
Hi Andrew, you surprise me! How come this limiting factor? Each axis has its own driver. Isn't the current simply limited by that hardware? So if you state that one motor could take 1A then the other 2 with the same driver should be able to tak…
Comment by
KlausK
July 2018
permalink
Yaw Jitter
Also, did you try automatic calibration? You can do it just for Yaw axis.
Comment by
KlausK
July 2018
permalink
Optimal input voltage for BaseCam SimpleBGC 32-bit Extended on the bench? Total max motor current?
The bord specs state Maximum motor current 1,5 A, so it should ber per motor.
Comment by
KlausK
July 2018
permalink
Yaw encoder on BaseCam SimpleBGC 32
I mean, there is no connections provided on the board other than the socket for the IMUs. So, I would solder it to the IMU connections, right?
Comment by
KlausK
February 2018
permalink
Not connected Bluetooth
Stop-Bit should only be one....thus: AT COMMANT --------> AT+UART=115200,0,2 And if neccessary Role=Slave: AT COMMANT --------> AT+ROLE=0
Comment by
KlausK
February 2018
permalink
Gui 2.63b0 New parameter «Hardware» — «Outer motor tilt angle»
Thx. "Follow device" means the follow mode? Too bad, I have the turnigy 5208 motors ... hard to fix the encoders magnet. Maybe I can glue it to the 6mm axle. I wonder, if the magnet has to be highly exact or if the encoder corrects minor i…
Comment by
KlausK
December 2017
permalink
Gui 2.63b0 New parameter «Hardware» — «Outer motor tilt angle»
Now starting to build, I've 2 more questions: I am not using encoders - would this be necessary to tilt the outer motor? And how is the orientation of the frame IMU? Parallel to the roll-axis or to the outer motor? Here is a schematic drawing -…
Comment by
KlausK
December 2017
permalink
Gui 2.63b0 New parameter «Hardware» — «Outer motor tilt angle»
Great! Thanks Aleksey for that fast and complete answer!
Comment by
KlausK
December 2017
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
KlausK
Joined
December 2017
Visits
39
Last Active
September 2018
Roles
Member
Powered by Vanilla