Patscherpofel

PWM output problem
I was about to give up on this and then I saw aux 1 is output 4 I think the others dont work aux1 one on the aerialpixel website...I think this is actually aux3 on mine...since aux1 is on aux 3 when I use sbus with encoders version what a mess !

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
yes I used adaptive tuning on basic settings, I already thought about disabling it, probably dosent make sense with encoder anymore? high sensitivity , yes I tried this on older gimbals, could make sense, would have to try this I didnt like the lp…

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
thanks Garug, allways apriciate other ideas I did try the new fw and also and pretty much maxed out D (between 200 and 255) it felt like raising P was locking the gimbal better I also tried low power and high power but all this didnt help at all …

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
its a bit hard to see because the video is very compressed but it almost looks like you have some tiny shakes also , and your camera might handle them better is it a gopro on medium wide settings? also a gopro in the housing is more aerodynamic …

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
same camera on 8bit board gives better results with the leaf blower and now that I compare this holding it by hand and compare it against each other without encoder it feels that it locks the angle tighter so my question now , are the motors or e…

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
no good reslults with a leaf blower I will have to compare this to other setups I have

Comment by Patscherpofel February 2016 permalink
EC45EN Brushless Gimbal Motor with Encoder
that was my though too, and I checked this -vibes are limited pretty much as good as it gets (perfect props and and good working dampening system -same copter handles a normal setup absolutely perfect in high speed I might l do a test with an …

Comment by Patscherpofel February 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
ok , so now its working good for several minutes cant post a picture of the inside , dont want to take it apart now :) but basically you have to check the part with the magnet that also holds the bell in place the loctite they used is either .. n…

Comment by Patscherpofel January 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
yes I will they basically did a poor job on the loctite one of three motors was ok will power the gimbal up now and see how it goes

Comment by Patscherpofel January 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
bingo! I opened the motor with the loose bell the magnet sits on the piece that secures the bell against the motor, all this was completely loose, and they didnt use lock tight on it! will use proper lock tight now and report back!

Comment by Patscherpofel January 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
just to be sure my Gimbal is ...camera-pitch -YAW-roll could this be a problem since there is no way to set this up in the software correctly?

Comment by Patscherpofel January 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
thanks for help! this motor with AS5048A http://www.etecpower.com/html_products/EC45EN-81.html the strange thing is that it affects all 3 motors , but never more then one at a time one roll motor has become a loose shaft after all this tuning, so t…

Comment by Patscherpofel January 2016 permalink
ENCODER Gimbal- random Motor suddendly looses all Power until recalibration
so I tried a lot more I started from scratch with the newest fw , GUI and Board and same thing no matter what I try.. -4s or 6s -little output power or maximum output power -warming and cooling model on or off after a bit of time one motor just dec…

Comment by Patscherpofel January 2016 permalink

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: Patscherpofel
Joined: January 2016
Visits: 20
Last Active: March 2017
Roles: Member