ariellago

Yaw encoder problem
Thank you very much Alex. I will try to see the magnet of the encoder, maybe it is the other way around since the distance of 1mm respects it. Thank you

Comment by ariellago May 2021 permalink
Yaw encoder problem
video

Comment by ariellago May 2021 permalink
High torque motors
in case there was any doubt about a large engine, here is a link. Could this motor be capable of moving 100kg of load? http://shop.smc-powers.com/PM20040-M?search=PM20040

Comment by ariellago November 2020 permalink
High torque motors
OK, I thought that it can be controlled through CAN, with the SimpleBGC 32 Bits CAN_MCU controller. Thank you

Comment by ariellago August 2020 permalink
Motor with gearbox
What is the minimum resistance in OHMS for the motor winding that can work properly on Basecam controllers?

Comment by ariellago October 2019 permalink
Motor with gearbox
It is interesting AOPEN, but I would like to improve this motor, since they have Backlash. I would like to use a Harmonic reducer, but I don't get the motor to have more revolution for this. One solution is in the motor winding, but I would not…

Comment by ariellago October 2019 permalink
Motor with gearbox
Do you know any controller that has gyroscopes for these motor that are as reliable as the basecam?

Comment by ariellago October 2019 permalink
re-fitting a Ronin Gimbal
The ronin 1, has electronic integrated to the motors, would have to destroy part of the ronin for it. Even so, I wouldn't get good results if I started from scratch with another gimbal. There are brands from China that sell something similar if…

Comment by ariellago October 2019 permalink
Yaw Encoder problem
The image capture was uploaded to DropBox, you can click on each icon to view it correctly

Comment by ariellago June 2018 permalink
Yaw Encoder problem
Previously, I had said if the normal software would work to use only the YAW encoder and they said no. It is only to test. That's why I got the license. Direct question: Is it possible to use normal software (without paid version of decoders) t…

Comment by ariellago June 2018 permalink
Yaw Encoder problem
Capture of the first image: https://www.dropbox.com/s/5bzb28k6as5rhxp/Captura.JPG?dl=0 capture of the second image of Debug tab: https://www.dropbox.com/s/gitah1cm8itog8t/Captura problema.JPG?dl=0 Thanks

Comment by ariellago June 2018 permalink
Yaw Encoder problem
Yes, I have only the encoder on the Yaw Yes, I also have the RC repeater I will inventigate with respect to the "Resquet State" tab since I never use it before.

Comment by ariellago June 2018 permalink
Roll gets unstable when pitch is 90 degree up or down
I did the same, install the software 2.60 and it was solved. But, I would like to know what the inconvenience is. Greetings.

Comment by ariellago December 2017 permalink
Yaw encoder
the gimbl does not work well if you only have the YAW encoder?

Comment by ariellago December 2017 permalink
Yaw encoder
Does anyone know if the standard version works the YAW decoder?

Comment by ariellago December 2017 permalink
YAW encoder is crazy ...
Hello Garug How could it be a problem with Magnet? The Motor works, but sometimes it does that. And it's not the only gimbal that does that, I've seen it in several.

Comment by ariellago November 2017 permalink
YAW encoder is crazy ...
I have a similar problem, which in a position of the YAW, makes me strong spasms. It only does it in the YAW. What can be?

Comment by ariellago November 2017 permalink
Important PROBLEM!!!
Thanks Garug, I was able to solve it with his advice. Thank you thank you thank you!!

Comment by ariellago August 2017 permalink
OFFICIAL PETITION: To update SimpleBGC App
Since the recent software updates, could not be controlled with the phone. Are there any versions that are being tested? Are they going to make it work, or do we have to think that it will not be able to be used anymore? Thanks for any specific answ…

Comment by ariellago May 2017 permalink
PLEASE PLEASE PLEASE HELP
If you buy Chinese gimbal , that is the main problem.

Comment by ariellago June 2016 permalink
What is the best engine to use encoders?
Thanks Garug, I am using 32-bit Basecam iFlight 100% original. I also see that the motor GBM 8108 reach 15.2 ohms, but I have to get to 24 volts. Affect the motor warm, albeit with encoders operating at very low temperature when at rest, but I wan…

Comment by ariellago May 2016 permalink
Motor Brushless gearbox
I consider BASECAM has done a very good job in their software. It can be applied to large STABILIZED HEAD, but we must work on its design, it is not easy, of course. If we used small brushless motors with a winding for helicopters, achieving the eng…

Comment by ariellago February 2016 permalink
Motor Brushless gearbox
Yes Garau, I thought about all the options. Encoders seems like a great solution, but imagine this: Suppose you want to make a gimbal cameras over 25 k. As a larger and heavier gimbal, throttle response is much slower. If you use a reduction on all …

Comment by ariellago February 2016 permalink
Motor Brushless gearbox
Thanks Garug, We wanted to try with the following engines: GB110 and GB8036, will be fast enough?

Comment by ariellago February 2016 permalink
Motor torque at 2.56b8
If 8-bit controller have more torque than 32 bits. I wonder if there is any way for 32-bit controllers have more torque

Comment by ariellago February 2016 permalink
Large motors to move over 40kg!
Well, I would resume this conversation. Anyone know how we can reach the maximum power of the big motors? There will be a new electronics Basecam, powerful enough for large motors, or be a PWM amplifier? Anyone have any idea?

Comment by ariellago January 2016 permalink
Roll loses horizontal angle randomly
all very nice, but the problem is solved when you have a 32-bit controller. So the problem is not GPS, but software or hardware. I had the same problem with controllers 8 bits, until I get tired of calibration.

Comment by ariellago January 2016 permalink
Large motors to move over 40kg!
if I had to make the biggest and most powerful engine that you can use with the controller SBGC as could be and how hard would it have?

Comment by ariellago January 2016 permalink
Large motors to move over 40kg!
It has 3 phases as any brushless motor gimbal. Each phase is 29 ohms. It is a little high.

Comment by ariellago January 2016 permalink
Large motors to move over 40kg!
Working in the film industry over 15 years ago. I am with this project over five years ago, even before he left the gimbals drivers. This motor is very expensive, about U$D1000 approx. If one could avail maximum power with BGC controllers can be use…

Comment by ariellago December 2015 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: ariellago
Joined: February 2014
Visits: 356
Last Active: January 24
Roles: Member