AlexLichi

Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I set up. It is working =) Thank you, Garug, for not letting me surrender)) I replace IMU and gimbal is work, maybe first IMU damaged or it was important physically to use this one as a "Camera IMU" But before that, when I used both of t…

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
The wire is ok. I test it.

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I unplugged the wire from the second IMU and reconfigured camera IMU with short wire. It did not help. I became a GUI on the second computer - there is the same delay I bought Alexmos controller + 2 IMU in the set. So I believe that they belong to…

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I2C indicator on the IMU or on the alexmos controller? I see on IMU only 1 led. And alexmos controller has 1 green and 1 red

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
Now I ordered one more Alesmos 32 bit controller and Evvgc

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I read the official instruction. More power to motor do not solve the problem. Everything moving freely and correctly balanced, yes. >"If you press the motors off on GUI and move the camera by hand, do the indicators on right side of the GU…

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I activated frame IMU and I tried to start without frame IMU - only with camera IMU - nothing changed. GUI and FW same. My motors 22 poles. If I start AUTO to configure motors then alexmos controller start beeping 3 minutes and gimbal sometimes don&…

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
Where are you that camera not installed? On all my videos and photos camera installed and balanced. 1) I set NUM.POLES 22. 2) Calibrated 2 IMU each in 6 positions and gyroscope. 3) Motor power ROLL, PICTH, YAW 30 4) PID 5-0-5 and after 2-0.5-1 After…

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
>"The GUI will take some seconds to connect, so what?" NOT this. I said delay from sensors to GUI

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
I tried to configure, but too many errors and too long delay info from sensors. It's simply defective. For Example: errors in recording sensor configuration, my last video:

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
When I turn gimbal and only after 10 seconds I see in GUI turn. A very long delay. But it must be instantaneous! I see in videos that it instantaneous. Is not it? I'm starting to think that he's just broken.

Comment by AlexLichi April 2017 permalink
Gimbal is going crazy. Motor is missing steps / Serial data corrupted. Alexmos 32 bit error
Which one? I calibrated 2 IMU each in 6 positions.

Comment by AlexLichi April 2017 permalink

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: AlexLichi
Joined: April 2017
Visits: 2
Last Active: April 2017
Roles: Member