matt_555

Yaw keeps shaking
I havent had a chance to look at mine either yet, but for me when I have Power=255, on 3 cell, P=10 I=0.1 D=255 is the only situation where I dont get shaking, this is on both YAW and ROLL. My pitch is fine with "normal" vaules.. I am gue…

Comment by matt_555 July 2016 permalink
Yaw keeps shaking
I also have a DYS Eagle eye with Iflight 5208-200 motors. I was using 3cell, but I am going to try with 4cell and encoders as I built mine with encoders, but didnt have them plugged in on the initial test. My shaking was low frequency i.e. slow lon…

Comment by matt_555 July 2016 permalink
Yaw keeps shaking
I think I have a similar problem, what gimbal, motors frame are you using? If you put D = 255 what happens? Thanks, Matt

Comment by matt_555 July 2016 permalink
LeViteZer Gimbal test videos.
Garug, I would just like to thank you for taking the time to publish these videos and to help others, your gimbals are a work of art!! p.s. it would be awesome to see the footage from the actual camera, on the boat, un-proccessed to see how stable…

Comment by matt_555 June 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Hello, I tested my DYS Eagle Eye 3 axis gimbal today with 1 click camera and frame (built in) IMU calibration. My board is version 3.6 with encoders (New Extended board) and I am using GUI + Firmware 2.59b1 as thats what came pre installed on my bo…

Comment by matt_555 June 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Quick Update, I returned my controller for the new extended version meaning im probably one of the first to get and use the new version of the board. I wanted a controller case, so I have had to adapt a 32bit simple case to fit the new extended bo…

Comment by matt_555 June 2016 permalink
LeViteZer Gimbal test videos.
Very Helpful! Thanks for taking the time to make these will definately help me! Can't wait for the rest of the videos! Thanks, Matt

Comment by matt_555 May 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Hello Garug, thanks for the info : ) Running the encorder wires seperate from the motor wires would be pretty difficult. I could run 1 wire inside the carbon tubes and then 1 wire outside the tube, but the wires will be running in the same directio…

Comment by matt_555 May 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Hello, I have decided that as I will not likely use my hand held gimbal with rc I may as well keep the current 32bit simlplebgc controller I have. I have a question about wires and wiring? What is the best thickness wires for motor wires and enco…

Comment by matt_555 May 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Bit of an update, my ipower motors fitted with encoders have arrived and my DYS gimbal frame is due to arrived Thrusday. I ordered the Simple 32bit alexmos from the site and then realised that maybe I should have ordered the new Extended version w…

Comment by matt_555 May 2016 permalink
3-Axis Handheld DSLR Gimbal parts list advice.
Hello Garug and AOPEN3434, Thank you for your posts and the helpful links. The main reason I looked at eagle eye frame is because I could get one cheap and it seems others have used it with moederate success. I understand that it might not be qui…

Comment by matt_555 May 2016 permalink

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: matt_555
Joined: May 2016
Visits: 71
Last Active: February 2017
Roles: Member