AndrewSupport

Can't power on CAN MCU board through battery
Hello Accel, To supply CAN_MCU board form the battery, you need to close "Power switch" pins here: http://ybex.com/d/i07i0w8tze8f2z44udf8xgev4v8lm2f07f2wc1ja.html Please, confirm that and tell us about result. Thank you.

Comment by AndrewSupport June 2019 permalink
3 PIN - SPI Encoder (AS5048a)
Hello, No way, because SPI connectipn type requires 6 wires. Likely, on your photo cable from PWM connection type. To help you more in detail, please, tell us type of controller used and type of encoder (with photo).

Comment by AndrewSupport April 2019 permalink
Gimbal motors for moderate load
Hello, Except motors, gimbal should have wide range for balacing camera with lens. Because without balance even motors with excess power won't be able to manage with their task. Please, specify, what battery do you plan to use for your gimbal?

Comment by AndrewSupport April 2019 permalink
32bit Extended Built in Frame IMU
Hello, As I understod you correctly, you have the Extended board kit with CAN IMU, like there: https://shop.basecamelectronics.com/product/simplebgc-32bit-extended-can-2-imu-set/ CAN IMU already ready to use as Camera IMU. If you already soldered t…

Comment by AndrewSupport April 2019 permalink
Problems with PWM Bypass
Hello, Your joystick has a wide otput options: http://ybex.com/d/zru1z5fw6vxqx2uflej4xjt3yuymw744ldaf5ukq.html Could you specify part number of used joystick?

Comment by AndrewSupport March 2019 permalink
Connect everything without mistakes.
Hello, This is a wrong motor connection: This motors has a three phase wires, these wires should be connected to three contacts of motor output, for example: http://ybex.com/d/qr802wwn4luj8u0ut94chiqxzb8d2tglifd1dode.html 12\14V output - this is sup…

Comment by AndrewSupport March 2019 permalink
Tiny Rev B I2C connector?
Hello, IMU connector on the boards: TE 1734709-4 http://www.digikey.com/product-detail/en/1734709-4/A99957TR-ND/2077864 IMU connector on the cable: 1470364-4 http://www.digikey.com/product-detail/en/1470364-4/A99933-ND/2077840 And pins: http://www.d…

Comment by AndrewSupport March 2019 permalink
Camera IMU Not connecting on the Tiny RevB
Hello, Plese, make a support request here: http://www.basecamelectronics.com/support/

Comment by AndrewSupport February 2019 permalink
BaseCamBGC Pro - Wiring diagram?
Hello, Dear customer, bit Brushless motors has three wires (connected to three phases inside) and connection method does not matter. Likely, on your photo motors with built-in I2c_drv module. Could you place link to the same motor here?

Comment by AndrewSupport February 2019 permalink
Sudden movements to stabilize pitch
Hello, Your motors has 14 poles: http://ybex.com/d/l3dkmg0jlbykuznx694khktm8sbeasylz77j9stm.html Correct the value and repeat tests. Tell us about result. Thank you.

Comment by AndrewSupport February 2019 permalink
Speed of motor won't change
Hello, If I understand you correctly, you are trying to control the motor with our controller as with ESC. Our system this is stabilisation system. You can't just manupulate rotation speed with our controller. Rotation speed depends of error si…

Comment by AndrewSupport January 2019 permalink
Battery connector
Hello, Onboard battery connector: https://www.digikey.com/products/en?keywords=B2B-XH-A(LF)(SN) And oncable battery connector: https://www.digikey.com/product-detail/en/jst-sales-america-inc/XHP-2/455-2266-ND/555485 Pins: https://www.digikey.com/pro…

Comment by AndrewSupport January 2019 permalink
Power Connector Name
Hello, Onboard battery connector: https://www.digikey.com/products/en?keywords=B2B-XH-A(LF)(SN) And oncable battery connector: https://www.digikey.com/product-detail/en/jst-sales-america-inc/XHP-2/455-2266-ND/555485 Pins: https://www.digikey.com/pro…

Comment by AndrewSupport January 2019 permalink
Power is not set: Driver Fault (under-voltage, over-current, short circuit)
Hello, Try to check these values: http://ybex.com/d/1vs93bgdoqfbnpwq28rl0gyo7v9lk6mtmfd3xa2p.html Power parameter should be above zero.

Comment by AndrewSupport December 2018 permalink
Over-Temperature protection
Hello, Assigment of I\O connectors can be find in products page: http://www.basecamelectronics.com/pro/ For exaple: http://ybex.com/d/pemqvhty0z3ttisy098b9k9zd7mra8ed8pgp5zws.html "When I connect Pro contoller to the PC, over-temperature prote…

Comment by AndrewSupport December 2018 permalink
bestablecam H4 - big problems
Hello, First of all, try update VCP driver from here: https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers And if errors (in the GUI) still exist, try connecting the controller to another PC with another USB cabl…

Comment by AndrewSupport November 2018 permalink
Setup for 3 axis head-tracking on a fixed wing aircraft.
Hello, Yes, "Angle mode" suitable for head-tracking. More answers here: http://forum.basecamelectronics.com/index.php?p=/discussion/699/yaw-using-a-rc-radio/p1 Also, I would recommend putting stiffeners on this part, like this: http://yb…

Comment by AndrewSupport November 2018 permalink
Problem after restarting, if signal is presented on Aux1
Hello, What firmware are you using? Did you try to use latest stable 2.63b0 firmware?

Comment by AndrewSupport November 2018 permalink
Yaw drift and more problem
Hello, Does your gimbal use Frame IMU sensor? What firmware are you using? Try enable this option: http://ybex.com/d/tu0l25nenbgkflaf5qoinvc9eaa41ku7brcvxxwy.html

Comment by AndrewSupport November 2018 permalink
Новый тип стабилизатора для кабельных систем для ПРО 360 камер. Подбор комплектующих для
Здравствуйте, Да, Tiny revB потянет этот мотор. Для подвеса вашей конструкции и контроллера Tiny, стоит обратить внимание на сопротивление обмоток, т.к. контроллер Tiny revB имеет придельный ток двигателей в 1А. https://www.basecamelectronics.ru/si…

Comment by AndrewSupport September 2018 permalink
Как быстро может вращаться двигатель, при управлении с RC пульта?
Уточните еще один момент, в режиме сервопривода, вам необходимо управлять CAN_Drv через основной контроллер (Serial API) или напрямую?

Comment by AndrewSupport August 2018 permalink
Как быстро может вращаться двигатель, при управлении с RC пульта?
Здравствуйте, Наша система - это система стабилизации. В данный момент, Вы не можете использовать её без датчиков IMU и в режиме сервопривода. В ближайшем будущем, мы планируем выпустить специальную прошивку для CAN_Drv модулей, для работы модуля в…

Comment by AndrewSupport August 2018 permalink
Please clarify motor current SimpleBGC v3.x
Hello, Line in the specification "Maximum motor current 1,5 A" - tell only about motor maximum current which can be provided to motors suppply. Full control board consumption consist of: motors current, load to 5V line (onboard 3.3V dc-dc …

Comment by AndrewSupport July 2018 permalink
Optimal input voltage for BaseCam SimpleBGC 32-bit Extended on the bench? Total max motor current?
Hello, Maximum motor current 1,5 A - total current for three motors. For example, one motor can take 1A, two other 250 mA each - but the total current should be no more than 1.5A.

Comment by AndrewSupport July 2018 permalink
Mini BGC 1.2 can support Encoder?
Hello, No, if your board looking like this: http://ybex.com/d/glu0wzskkg8lmrkqmdtatnztgsx9fdxx4t8ysj8e.html If your board looks different, make a photo of both sides of you r board, upload to dropbox.com and place link here.

Comment by AndrewSupport July 2018 permalink
Yaw Encoder problem
Hello, Try to check the connection with YAW encoder, if you use PWM connection type: http://ybex.com/d/cxc00rvsdsiymsnt27w4oq2psdfu0lcbjwaljtq9.html "Direct question: Is it possible to use normal software (without paid version of decoders) to …

Comment by AndrewSupport June 2018 permalink
Yaw Encoder problem
Hello, Please, place only links to your screenshot here. "Yes, I have only the encoder on the Yaw" - if you use only one YAW encoder, you should to use only regular firmware. Because encoders firmware require encoder on each motor.

Comment by AndrewSupport June 2018 permalink
Encoder angle limits do not work
Hello, Please, make a video with your problem, upload to Youtube and place link here.

Comment by AndrewSupport June 2018 permalink
Yaw Encoder problem
Hello, Are you use gimbal only with YAW encoder? Did you try push "request state" button on Debug tab when the problem was appear? Place screenshot with result here (by dropbox.com or similar service). Do you use RC control or something el…

Comment by AndrewSupport June 2018 permalink
Frame imu fried?
Hello, If your board can't get data from IMU, try to check this: http://ybex.com/d/8bic62798dwvgkesxjv5kx8m7d5e8hnzx9cx9ha8.html This is inductive filter: https://www.murata.com/en-us/products/productdata/8796743204894/ENFA0008.pdf On DYS board…

Comment by AndrewSupport June 2018 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: AndrewSupport
Joined: October 2014
Visits: 399
Last Active: February 15
Roles: Member, Administrator, Moderator