fedevision

8bit/3axis Roll with slow oscillations
Yes, no EEPRON erase on this GUI, checked the gimbal arms and were a little off 90 degrees, that helped too. Will test gyro cal on startup off, always used on. Last question (hope), I use IMU sensor attached directly on top of camera (GPH3+) aligne…

Comment by fedevision August 2015 permalink
8bit/3axis Roll with slow oscillations
Firmware is 2.40b7, yes, follow offset performed, will try erase EEPROM to start from scratch, but don't know how to do that erase on 8bit controller, any link? Thank you !

Comment by fedevision August 2015 permalink
8bit/3axis Roll with slow oscillations
Hi Garug! In my case, fails when Follow Mode activated. I'm using Pitch Tilt channel on RC only, and FC Roll with AUTO gain 8, tested FC Roll Off, didn't help. On Real Time Data I can watch the roll line making waves when I move the frame …

Comment by fedevision August 2015 permalink
Real time data graphic
The graphic on aerialpixels site didn't help me, that's why I'm asking for help.

Comment by fedevision December 2014 permalink
DYS Smart GoPro Gimbal connection question
GeoEnzo, when that happens to my pc, I disconnect usb cable, wait a few seconds, reconnect and it starts working.

Comment by fedevision October 2014 permalink
DYS Smart GoPro Gimbal connection question
Just saw your post on RC forum and I saw you have a very custom setup, maybe would be a good idea to check some videos on youtube with similar setup of yours.

Comment by fedevision September 2014 permalink
DYS Smart GoPro Gimbal connection question
I tested other options on GUI, on Rc Settings window, there I used PMW for pitch, other options did not work for my setup.

Comment by fedevision September 2014 permalink
Hardware or software tune problem?
Thank you Garug, 1. Checked new propellers before installation, came factory balanced. 2. Checked, ok. 3. Checked, ok. One detail I found today is that I inverted one arm of gimbal, that way is easier to connect usb/hdmi cable and take gimbal or …

Comment by fedevision September 2014 permalink
DYS Smart GoPro Gimbal connection question
Hi, I use PWM, tested with some of the other options and did not work. GL

Comment by fedevision September 2014 permalink
Hardware or software tune problem?
After almost a month of testing, twisting, de-soldering, re-soldering, tightening bolts, de-installing, reinstalling, downgrading, upgrading, lots of frustration, getting crazy, etc, think I almost have it tuned, but not sure if issue is with roll o…

Comment by fedevision September 2014 permalink
Can't see entire GUI's window
Warning on this method! The use of too high resolution could damage permanently the graphic board, don't go more than one step up! Do not use with high demand graphics (like games) software.

Comment by fedevision September 2014 permalink
Gimbal Issues with getting setup
Check this one, probably related: http://forum.basecamelectronics.com/index.php?p=/discussion/762/virtual-port-not-showing-up

Comment by fedevision September 2014 permalink
DYS smart 3 axis
http://aerialpixels.com/support/alexmos-brushless-gimbal-controller-simplebgc-tuning-guide/

Comment by fedevision September 2014 permalink
Can't see entire GUI's window
Thank you Garug. Got it solved with this method: http://www.taringa.net/posts/hazlo-tu-mismo/16379655/Tutorial-forzar-resolucion-laptops-windows-7.html Use translation if necessary but pictures are clear enough.

Comment by fedevision September 2014 permalink
Hardware or software tune problem?
Yes, works well in hand, going to check all that starting with hardware, thanks!

Comment by fedevision August 2014 permalink
Boards compability
In this case, upgrade didn't work, I'm glued to 2.2b2, but works well, still have some fine tuning to do. Thanks

Comment by fedevision August 2014 permalink
Boards compability
Thank you both for your answer, the gimbal is a Hobbypower, bought on March on Amazon, and the expansion board is from gadgetextreme on Ebay, received yesterday. Anyway, took the chance today and soldered them, then tested using 2.2b2 (fw that came…

Comment by fedevision August 2014 permalink
Diy gimabal frame here
http://www.image-share.com/ijpg-2643-12.html

Comment by fedevision August 2014 permalink

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: fedevision
Joined: August 2014
Visits: 35
Last Active: September 2015
Roles: Member