About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
ehinnphoto
Activity
Discussions
2
Comments
9
Message "motor is missing steps" what does it mean?
having the same issue. I get the motor is missing steps error and now my gimbal is shaking like crazy. The shaking happens every time I upgrade firmware.
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
When I configure auto it goes through all the progressions, then around the last 1 or 2 steps it starts shaking and going crazy again. Motors shut off everything moves logically. Im going to have to send it back as the last time I tried it shook a…
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
I had to flash back to previous firmware and my battery is fine and the motors powered up again. But I still have the same problem with the gimbal shaking and turning violently. I have cleared all settings and started over from scratch and STILL e…
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
and the problems just keep on coming! Tried the basic setup didn't work. Tried recalibrating the IMU with no success. Now my motors won't even power on. First instinct says it's the battery but I charged it overnight and literally …
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
As soon as I raise any P or D value over 0 it goes crazy. Meaning if I set it to 1… it starts jumping.
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
Retune from here though? I wouldn't even know where to start.
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
Ok excuse my ignorance clearly the above listed was the software not firmware. I just upgraded to firmware 2.41 b4 from 2.40 and HELP all my setting have gone crazy! Everything double or tripled and is seemingly way too high as Im getting super st…
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
Insert noob question here- put the gimbal to the position while holding it it manually? or with the motors on tilt up til it's in position and then retune?
Comment by
ehinnphoto
August 2014
permalink
Shakes and (guess what) more shakes
Simple BGC GUI v2.41 b5
Comment by
ehinnphoto
August 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
ehinnphoto
Joined
August 2014
Visits
3
Last Active
August 2014
Roles
Member
Powered by Vanilla