About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
nnikba
Activity
Discussions
1
Comments
10
Follow mode = I am getting crazy
I may have the same problem, All is working fine except when choosing follow yaw mode. Can you describe again the way you solve, it? Upload a old firmware, and upload again the new one and that's it?
Comment by
nnikba
December 2013
permalink
Elastic band
Please follow http://www.visionrouge.net/web/2013/12/diy-alexmos-gimbals-vs-freefly-movi/ to see what I'm talking about.
Comment by
nnikba
December 2013
permalink
3 motors or 4 motors for RED
Kikojiu, What is the weight of your camera setup please? Red + lens + follow focus + wireless transmitter + batteries?
Comment by
nnikba
December 2013
permalink
Elastic band
I have look further on the M10 one, the motor are completely different. Feedback is given by an external sensor on each axis, this is no the same brush-less motor they are using. I will post soon the differences on my blog.
Comment by
nnikba
December 2013
permalink
Elastic band
Yes, I have tested the real FreeFly M10, and motor are holding even if you force them by hand, no loss step, it come back smoothly. I guess that the difference between a 1000 USD and a 15000 one's
Comment by
nnikba
December 2013
permalink
Follow Pitch Roll Yaw on version 2.3b5
I have exactly same problem, I put off for all input I don't use, but it's not changing much. The only think I'm suspecting is a bad reset when I change mode, cause if I keep resetting with a long press on the button. Sometime it'…
Comment by
nnikba
December 2013
permalink
All is working except follow mode
Sorry for the good new, it's seems now it's an intermittent problem, Some time it's working fine at the start, sometime not? I have look for soldering/cable problem without any success...
Comment by
nnikba
November 2013
permalink
All is working except follow mode
Ok, I found out by myself and I think it's quite important to communicate about it. I always fond that the "invert" in the motor configuration did not change anything. But in the follow mode, it's very important to get it right.…
Comment by
nnikba
November 2013
permalink
All is working except follow mode
I can read: "In this mode, the position of the outer frame by all of 3 axes is estimated from the motor's magnetic field. " So I'm assuming I have interaction with this reading but have no idea how can I fix this or increase it…
Comment by
nnikba
November 2013
permalink
All is working except follow mode
Thanks fo rth efeedback, This is what I have. (and want) Profile 1, no follow, work great Profile 2, Folow RC for yaw and tilt, work great. (with PS2 Joystick) Profile 3 Follow mode pan and tile, not working. (no joystick control of course) During…
Comment by
nnikba
November 2013
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
nnikba
Joined
September 2013
Visits
10
Last Active
December 2013
Roles
Member
Powered by Vanilla