About us
Products
Controllers
Comparison chart
SimpleBGC 32-bit
Tiny+ Rev. C & D
The smallest 3-axis stabilization controller
SimpleBGC 32-bit
3-axis stabilization controller
SimpleBGC 32-bit Extended
3-axis stabilization controller
SimpleBGC 32-bit
Extended Long
3-axis stabilization controller
SimpleBGC 32-bit
CAN_MCU
3-axis stabilization controller
SimpleBGC 32-bit
OEM
3-axis stabilization controller
BaseCamBGC Pro
All the power of 3-axis stabilization
Components
GPS IMU v.1.2
Improved precision of stabilization
WiFi UART
WiFi for SimpleBGC boards
AS5048B Encoder
On-axis magnetic
encoder
I2C IMU Rev.B
Updated version
of I2C IMU
I2C Extender
Provides reliable I2C communication
CAN_Driver
Enables CAN-bus
for SimpleBGC boards
BLE Serial Adapter
Bluetooth capability
for SimpleBGC boards
CAN IMU
Next generation IMU
RS422 Adapter
RS422 to SPI adapter for encoders
Archived
SimpleBGC 8-bit
2+1-axis stabilization controller
GPS IMU v.1.0
Improved precision of stabilization
Store
Retail Store
B2B Store
Software
SimpleBGC 32-bit v3.x GUI
GUI 2.60b4
— latest version
Previous versions
SimpleBGC 8-bit Downloads
Mobile App
iOS App
Android App
Encoders with SimpleBGC 32-bit
General information
Upgrade to Encoder firmware
Manuals
SimpleBGC 32-bit v3.x Manuals
2.6x
Video Tutorials
Connection Diagrams
Connection Diagram for boards ver. 3.0
Bluetooth connection for boards ver. 3.0
Tiny Board Connection Diagram
Encoders with SimpleBGC 32-bit
SimpleBGC 32-bit Encoders Manual
32-bit CAD drawings
Pro Controller CAD drawing
DWG
Extended Controller CAD drawing
DWG
Controller CAD drawing
DWG
Tiny Controller CAD drawing
DWG
Sensor CAD drawing
DWG
CAN IMU CAD drawing
DWG
SBGC32_I2C_Drv Expansion Module
General information
Connection Diagram
Reference Manual
Schematics
Other Manuals
Serial API
Scripting Language Reference (2.5x)
FPV Follow Potentiometer
Support
Forum
EN
CN
Discussions
Activity
Sign In
ProV
Activity
Discussions
4
Comments
8
Perfectly level until yaw
Do I need more power to the motors? I hate to mess to much with the PID, everything is working nice with no vibration.
Comment by
ProV
July 2014
permalink
Rolls when tilts
Thanks 200sx, When working with my copter and setting PID I like to raise it off the ground for eye level so I hang it. With that said, while its hanging sometimes it is not very level and when I power it up with gyro calibration set to automatic i…
Comment by
ProV
July 2014
permalink
Gimbal not level after tilt, hangs to the right
Have you resolved your issue. I am having the same problem, I didn't always have it but of course things couldn't run smooth all of the time. In GUI it shows my IMU is remaining level however as its tilting forward to 90 degrees it is cl…
Comment by
ProV
July 2014
permalink
So how screwed am I????
Sent the board in…..
Comment by
ProV
May 2014
permalink
So how screwed am I????
Here's another thing, powered by battery only-I connected the buzzer and it didn't make any noise. Uh-Oh…..
Comment by
ProV
May 2014
permalink
So how screwed am I????
Disconnected battery and all motors, powered only by USB. GUI, everything is normal -version,firmware,IMU settings -its all good. Controller board shows a solid red light, a very faint rapid flashing green light. The board seems to bit a bit warm…
Comment by
ProV
May 2014
permalink
So how screwed am I????
Fortunately that's not the problem, yet...the yaw connecting leads to the board were disconnected, plug type, while it was hooked up with usb also. But that's all it took for my board to say corrupted and I an unable to do anything once m…
Comment by
ProV
May 2014
permalink
Mac users: every step configuring 3axis gimbal for mac using alex mos
I am having the same issue, it looks like its been some time since your post, any luck?
Comment by
ProV
May 2014
permalink
Howdy, Stranger!
It looks like you're new here. If you want to get involved, click one of these buttons!
Sign In
Apply for Membership
About
Username
ProV
Joined
May 2014
Visits
18
Last Active
July 2014
Roles
Member
Powered by Vanilla