MShekunov

>5g micro brushless suppliers?
For what type of tasks you want to use such a gimbal?

Comment by MShekunov July 2015 permalink
6s lipo battery
http://forum.basecamelectronics.com/index.php?p=/discussion/1744/using-6-cells-battery-to-power-the-32-bit-board#Item_3

Comment by MShekunov April 2015 permalink
32 bit 3 axis BGC Red LED on IMU(s)
If it works, don't worry (until the smoke is going up) :) And we are very interested in pictures of your gimbal and IMU!

Comment by MShekunov April 2015 permalink
Houston, we have a problem: UART port SimpleBCG 8bit: pullup current too high (27mA) on
If you still doubt, just put 1k resistor serial into the line.

Comment by MShekunov April 2015 permalink
Houston, we have a problem: UART port SimpleBCG 8bit: pullup current too high (27mA) on
Input resistance of Rx-pin is too high. There won't such a large current. So you may connect your "Uno" directly with the gimbal controller.

Comment by MShekunov April 2015 permalink
Android App 2.43b9 with firmware 2.50b2?
tompa, jen, why wouldn't you try to? At a worst case, just roll back to previous firmware. Your experience will be useful for most of us!

Comment by MShekunov April 2015 permalink
No COM Port Available in GUI
Seems to be a hardware failure. Firstly, try another USB cable or use another PC to be sure that onboard converter is alive. Also, you may use external FTDI converter to connect with controller via UART. If nothing helps - contact to your seller.

Comment by MShekunov April 2015 permalink
Ipower 5208-200T
These two motors are almost identical. "Turns" - means quantity of wire turns around each stator teeth. More turns - more torque, but it also causes more DC resistance. I'd to advice you 4S battery. In that case you have a bigger rang…

Comment by MShekunov April 2015 permalink
Pitch control only works with USB connected - board v1.0 f/w 2.40 b7
cliffy, would be nice to look at the detailed picture of your controller here!

Comment by MShekunov April 2015 permalink
PWM RC_ROLL & RC_PITCH now working
Put here a couple of controller's detailed photos.

Comment by MShekunov April 2015 permalink
Good Controller Card ?
Our production doesn't sell at Ebay, Aliexpress etc. Items you asked are not original Basecam controllers.

Comment by MShekunov April 2015 permalink
Difference between Rctimer 5010-14 360KV and GBM5010-150T motors
No it can't. Please, use motors designed especially for the gimbals. Gimbal motors have DC resistance much higher than in other type ones.

Comment by MShekunov April 2015 permalink
Basic Balancing. (camera does not stay in tilted posistion)
You demonstrated the result of balancing, did you? If so, you did it wrong. Please, look at that example of balancing:

Comment by MShekunov April 2015 permalink
Bluetooth connection 32bit HC06 doesn't connect from GUI
Zeb, could you put here the picture of your controller with connected BT-module?

Comment by MShekunov April 2015 permalink
Power Voltage to 32 bit, board version3
http://forum.basecamelectronics.com/index.php?p=/discussion/1744/using-6-cells-battery-to-power-the-32-bit-board#Item_3

Comment by MShekunov April 2015 permalink
Slip rings - experiences
Guys, are you really using rotation more than 360 degrees?

Comment by MShekunov April 2015 permalink
Using 6 cells battery to power the 32 bit board?
We strongly don't recommend you to overvoltage the controller. It void of warranty. Otherwise, you may use step-down DC/DC converters.

Comment by MShekunov April 2015 permalink
Ok to pull an extra 340 mA from IMU 5V supply?
Sensor's power connection comes through the ferrite filter. According to documentation, filter's rated current is 100mA. http://ybex.com/d/ppfh48o9tmi0qpsqqd8yrbxg6fqrxmw2i03tsh0y.html But we tested it till 500 mA. Nothing happened. But p…

Comment by MShekunov April 2015 permalink
Gimbal won't power up unless power AND usb connected?
I proud of customers who can maintain a multimeter ))) By the topic, seems that your guess is right about broken voltage regulator. That is a pulse reg. AP5100. Try to find somebody who can help you with replacing of a broken component. It's …

Comment by MShekunov October 2014 permalink
ARMBGC 32bit burned
Full 6S is 25.2V This board support up to 25V. Please, contact the seller to solve the problem.

Comment by MShekunov April 2014 permalink
Voltage Error on the ArmBGC V 4.0 32-bit (Alexmos)
Dear customer, replacement of this component may solve the problem with a high probability. But be sure that you installing it properly! http://ybex.com/d/l0vk0n0cuhraf8edi2e4ed39dk764gd5t7i7vw5p.html

Comment by MShekunov April 2014 permalink
sensor is not connected, green flashing rapidly
Just can recommend you to return the board to your seller.

Comment by MShekunov April 2014 permalink
sensor is not connected, green flashing rapidly
Firstly, disconnect the expansion board and then SWITCH ON the main controller with sensor.

Comment by MShekunov April 2014 permalink
sensor is not connected, green flashing rapidly
Where did you buy the controller? Could you place here some photos of your controller? What happens if you directly connect a sensor to the board with shortest wires?

Comment by MShekunov April 2014 permalink
Mossfet Specification v2.2 board
IRF9335, SO-8

Comment by MShekunov October 2013 permalink
Motor pin configuration
If you talking about connection of gimbal motors to SimpleBGC controller, so you got to know that it is no matter the polarity. It is the same rule as you connect the BLDC motor to any ESC. If motor runs wrong direction, you can invert it in the GUI.

Comment by MShekunov October 2013 permalink
No motor output?
Did the PID-tuning changed a picture anywhere?

Comment by MShekunov May 2013 permalink
How can I figure out which side is up for small sensor board?
Twist your sensor in the hands, and look to GUI. It is a simple method to confirm axises.

Comment by MShekunov May 2013 permalink
Pan axis addon?
All boards you bought are compatible with 3-axis board. You should only update SBGC with the latest firmware.

Comment by MShekunov May 2013 permalink
Gimbal BL Motor GBM4008-150
May I answer? :) You can use this motors. They are specialy winded for gimbal use.

Comment by MShekunov April 2013 permalink

More Comments

Howdy, Stranger!

It looks like you're new here. If you want to get involved, click one of these buttons!

About

Username: MShekunov
Joined: March 2013
Visits: 71
Last Active: January 2016
Roles: Moderator